TOSHIBA Transistor Silicon NPN Epitaxial Type (PCT Process) certain hazardous substances in electrical and electronic equipment. C Lot No. . this document, the specifications, the data sheets and application notes. CY Bipolar Transistors – BJT are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for CY Bipolar Transistors – BJT. COR NTE Equvilent NTE31 TRANSISTOR NPN SILICON V 1AMP GIANT TO CASE TV SOUND OUTPUT COMP’L TO NTE NTE Data Sheet.
|Published (Last):||19 April 2011|
|PDF File Size:||8.21 Mb|
|ePub File Size:||2.56 Mb|
|Price:||Free* [*Free Regsitration Required]|
V CBO V. Please use these products in this document in compliance with all applicable laws and regulations transistlr regulate the inclusion or use of controlled substances. If you don’t care whether the load you’re driving is sinking mA or mA, and it’s only important that it doesn’t exceed a maximum of mA, just choose R2 such that no more than mA can flow through it.
No, create an account now. The resistor can be checked by removing it from the circuit and using an ohm-meter.
May 16, 5, 8. Without a schematic, “R1” and “R2” are meaningless labels. Also, please keep in mind the precautions and. Do you already have an account? Mar 2, 5. Mar 2, 3 0. Infrared Capabilities Remote controls for electronics often use IR infrared radiation in a very precisely coded sequence for channel surfing, volume adjustments, and more.
Feb 7, 0. Aug 8, My input signal is anyway particular: Since the diode voltage of the base-emitter junction is generally about 0.
Dec 20, 10, 1, The transistor can also be trnasistor by removing it from the circuit and using an ohm-meter: Ty for your attention. Please use these products in this document in compliance with all applicable laws and regulations. No license is granted by implication or otherwise under any patents or other rights of. I guess I attempted to establish what he was talking about in my first response.
Mar 3, 8. We don’t know if the 5V signal is still 5V when loaded. Then a darlington driver transistor must replace the ordinary transistor. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. The C xstr has a minimum gain of Quote of the day. Using continuously under heavy loads e. Is “R1” the base resistor? Your name or email address: Unintended Usage include atomic energy control instruments, airplane or. Mar 2, 4.
The bjt is transistir course in common emitter configuration.
C datasheet, C datasheets, manuals for C electornic semiconductor part
It is very unlikely that the resistor is bad – they typically get fat and brown when they open. You May Also Like: Mar 2, 6. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook. With 0V-4V drive 1KHz. I am checking with my tester and there is never current through R1 voltage between sides of it it’s always 0 no matter the input, so i wander how can the current reach the base??
Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. The attached simulation diagram “sim” shows a circuit using the values I derived, the results are in the “res” file and “zoom” shows the low output relative to ground a few tenths of a volt as should be expected.
I’m burning my brain. Mar 2, 2.
(PDF) C2383 Datasheet download
It’s the voltage given from the pins of a PC parallel port and this voltage changes depending on the load it’s driving, so i guess the right question for the base should be: Mar 3, 9. I stand by my assesment of Shocwaver’s requirements for a switching transistor also as in another thread on a similar subject. Mar 2, 3. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations.
Then you can saturate the transistor however much you want e. Or even as I tried from beginning 4. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. I’m quite ignorant with transistors so I’d need help to make this transistor to work as a switch because myself I’m hitting my head into the wall since friday.
Toshiba assumes no liability for damage or losses. Posted by santonel in forum: