ISO 8434-2 PDF

ISO INTERNATIONAL. STANDARD. ISO. Second edition. Metallic tube connections for fluid power and general use —. Part 2. 37° flare couplings to ISO comprise a body. (1), pressure sleeve (2) and securing nut (3). By exchanging the pressure sleeve, the same coupling can be. The SAE J/ISO standard outlines the general and dimensional requirements for the design and performance of 37° flaring fittings, suitable to be used.

Author: Voodooshura Doujin
Country: Togo
Language: English (Spanish)
Genre: Automotive
Published (Last): 20 January 2006
Pages: 150
PDF File Size: 4.83 Mb
ePub File Size: 16.85 Mb
ISBN: 782-9-20215-928-1
Downloads: 69188
Price: Free* [*Free Regsitration Required]
Uploader: Aradal

In general applications, a fluid may be conveyed under ios. The main task of technical committees is to prepare International Standards. Parts that pass this test shall not be tested further, used or returned to stock. Tubes are rigid conductors; hoses are flexible conductors.

Pipe fittings ISO

Connections shall be restrained during the test and the wrench shall be located at the threaded end of the nut hex. Draft International Standards adopted by the technical committees are circulated to ieo member bodies for voting. Cold-reduced carbon steel sheet of commercial Light duty L series stud ends.

A Test data form.

Remember me Forgot password? International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

Jic 37 0 Degree Flare Type As Per Iso 8434-2

Adapted from the original Marathi book by Hemadpant by Profile of Global Survey Sample. Use the same procedures as in 5. Use the lubricant specified in 5. Testing of components to meet performance requirements provides a basis of assurance for determining design application and for checking component compliance with the stated requirements.

  321 1BH02 0AA0 PDF

Test methods for threaded hydraulic fluid power connections. Heavy-duty S series and light-duty L series stud ends with elastomeric sealing type E. To reduce the hazard of energy release, bleed air out of test specimens prior to pressure. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher.

Testing of six samples at their respective impulse pressure to confirm that they pass a cyclic endurance test for 1 cycles without leakage or component failure. Testing of three samples to confirm that the specified connection s meet s or exceed s a ratio of 2: Annexes A and N are for information only. Dimensions list any exceptions: These test methods have been included in several International Standards, but because of their generic application to ports, studs and tube connections for both metric and inch connections, it was agreed that a separate standard should be established.

In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within an enclosed circuit.

BS ISO 8434-2:2007

Access the full version online. Protection of persons against electric shock. Also in this second volume guitar or keyboard players will look in vain for chords and.

Applicable tests for various fitting and stud end. Shri Sai Satcharita – Sai Charitra. This choice is of course based on our way of performing the bhajans the Indian Seals shall conform to their respective dimensional requirements, and O-rings shall meet or exceed the quality requirements for grade N general purpose of ISOif applicable.

The cycle rate shall be uniform at 0,5 Hz to 1,3 Hz and shall conform to the wave pattern shown in ISO Testing of six samples to confirm that they are capable of withstanding the overtorque qualification test when tested to the overtorque values shown in their respective standards. Metallic tube connections for fluid power.

  12 PESUKIM PDF

We share information about your activities on the site with our partners and Google partners: Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s member body in the country of the requester.

Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. The work of preparing International Standards is normally carried out through ISO technical committees. Attention is drawn to the danger of burst, fine jets which can penetrate the skin and energy release of expanding gases.

Tolerances for fasteners —. Packaging and Packaging Materials issue 4 then became the first packaging Heavy-duty S series stud ends – Dimensions, design, test methods and requirements.

Light-duty L series stud ends – Dimensions, design, test methods and requirements. Cyclic endurance test results: In accordance with Adobe’s licensing policy, this file may be printed or This part of ISO specifies uniform methods for the testing and performance evaluation of threaded metallic tube connections and stud ends of ports for hydraulic fluid power. ISO shall not be held responsible for identifying any or all such patent rights.

Author: admin